Automate AM1.5 Guide de l'utilisateur Page 19
- Page / 83
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
– 9 –
GAS TANK HEAT (When Specified)
Check the gas data plate attached to the dishwasher or the tag attached to the incoming gas piping
for the type of gas to be used.
The burner is not adjustable. The maximum
owing inlet gas pressure must not exceed
the Maximum value in the table. If line
pressure exceeds the Maximum value in
the table, an additional pressure regulator
(not supplied) must be installed in the
supply line.
Static inlet line pressure should not exceed 14" W.C. The minimum value is for input adjustment.
The gas valve is provided with a pressure tap to measure the gas
pressure downstream, which is also the manifold pressure. Gas
supply piping must have a sediment trap (supplied by others)
installed ahead of the dishwasher’s gas control. Connect the gas
supply to the
1
⁄2" NPT gas inlet underneath the machine (Fig. 11).
NOTE: DO NOT use Teon tape on gas line pipe threads. For
gas line pipe connections, use L
o c t i t e 565, Hobart part 546292,
or a exible sealant suitable for use with Natural and Propane
Gases.
The appliance and its gas connections must be leak tested before placing the appliance in operation.
Use soapy water for leak test. DO NOT use open ame. The installation must conform with local codes,
or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition). Copies
may be obtained from American Gas Association, Inc., 1515 Wilson Boulevard, Arlington, VA 22209.
The appliance and its individual shutoff valve must be disconnected from the gas supply piping system
during any pressure testing of that system at test pressures in excess of
1
⁄2 psig (3.45kPa).
The appliance must be isolated from the gas supply piping system by closing its individual manual
shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or
less than
1
⁄2 psig (3.45kPa).
Dissipate test pressure from the gas supply line before re-connecting the appliance and its manual
shutoff valve to the gas supply line. Caution: Failure to follow this procedure may damage the gas
valve.
The dishwasher must be installed so that the ow of combustion and ventilation air will not be
obstructed. Do not store material underneath the machine; air openings into the combustion chamber
must not be blocked. Make sure there is an adequate supply of make-up air in the room to allow for
combustion of the gas at the burner.
Keep the appliance area free and clear from all combustible substances. Do not obstruct the ow of
combustion and ventilation air. The dishwasher must have a minimum clearance from combustible
construction of 1 inch from the ue at the rear. Clearances of 20 inches out from the dishwasher at
the front (or left side in a corner installation) by 27 inches above the nished oor and 15 inches out
from the dishwasher at the right side by 27 inches above the nished oor must be provided for
servicing.
The burner is ignited automatically by solid state electronic circuitry; there is no pilot light. Gas ow
is regulated by the temperature control circuit.
Fig. 11
GAS PRESSURE SPECIFICATION
[FLOWING GAS PRESSURE — NOT STATIC]
Type
of
Gas
BTU/HR
Inches W.C. (Water Column) FLOWING
Incoming Line Pressure
Manifold
Pressure
Minimum Maximum
Natural 25,000 3.5 7.0 3.2
Propane 25,000 9.0 11.0 8.2
AM15 Dishwasher Technical Manual Page 19 of 83
- AM15 DISHWASHER 1
- TECHNICAL MANUAL 1
- 208-240V/60/3 1
- Need other Hobart Services? 2
- AM SELECT DISHWASHER 3
- DISHWASHER – ELECTRIC 4
- DISHWASHER – GAS 6
- AM SELECT 10
- DISHWASHER 10
- DISHWASHERS 11
- IMPORTANT 12
- FOR YOUR SAFETY 12
- TABLE OF CONTENTS 13
- SAVE THESE INSTRUCTIONS 14
- INSTALLATION 15
- Fig. 6 Fig. 7 16
- Fig. 4 Fig. 5 16
- Fig. 8 Fig. 9 17
- PLUMBING CODES 18
- 2 psig (3.45kPa) 19
- Fig. 12 Fig. 13 20
- Perimeter Calculation Formula 21
- Rate Calculations 21
- Fig. 16 Fig. 17 Fig. 18 23
- DETERGENT SENSOR PORT 24
- SHORTCUT IF 26
- PROGRAMMING BOTH FEATURES 26
- AT THE SAME TIME 26
- Fig. 23 27
- Sanitizing Mode 28
- Hot Water 28
- Chemical 28
- Fig. 28 Fig. 29 29
- MAINTENANCE 31
- TROUBLESHOOTING 32
- SYMPTOM POSSIBLE CAUSE 33
- CONNECTION 35
- TEST PINS = 36
- TEST PAD = 36
- SWITCH = 36
- FORM 43094 (October 2004) 37
- CONTROLSCONTROLS 40
- CONTROLS 40
- PL-57403 42
- PL-57414 44
- PL-57402 46
- PL-57399 48
- PL-57401 50
- PL-57407 52
- PL-57408 54
- PL-57400 56
- PL-57405 58
- DRAIN UNITDRAIN UNIT 60
- DRAIN UNIT 60
- PL-57413 62
- PL-57412 64
- PL-57406 66
- PL-57410 68
- PL-57411 69
- PL-57415 70
- PL-53023 72
- Online Parts Catalog 73
- User Guide 74
- Use SMARTPARTS Now 78
- Equipment) 79
- RECOMMENDED SPARE PARTS LIST 83
Produits connexes et manuels pour Alarme de voiture Automate AM1.5
(7 pages)
(41 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.530 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels